Aspiring Stunt Trooper in Greenville

[RogueTrooper]

and make sure the fown coms to a point at the ends:

[RWinsel]

the Helmet is looking good.

I would raise the rubber brow a wee bit

Thanks Tom! Whats the best way of doing that without taking the helmet apart?

And how's this for the frown?

[RogueTrooper]

can you show me a side views of the frown please?

and the best way is to loosen the ears bolts so you can have a little play (the rubber not soo tight against the face)'

remove the rubber brow and use the Hobby scissors to trim the plastic helmet brow back a wee bit.



Look at these screen used ANH Stunt helmets for a basic brow height :

[RWinsel]

Thanks Tom!

Hows this for the frown?

[RogueTrooper]

The frown could be w wee bit more pointy, but falls in the parameters.

[RWinsel]

The frown could be w wee bit more pointy, but falls in the parameters.

Alrighty thanks! Can you point me in the direction of how to assemble the forearms?

[RogueTrooper]

The frown could be w wee bit more pointy, but falls in the parameters.

Alrighty thanks! Can you point me in the direction of how to assemble the forearms?

I would use this for a start.

I would not use the CA glue but either E6000 or Amazing Goop

CA glue holds fast but is not water/moisture proof and will not hold after a point....

Video on the basics

https://www.youtube.com/watch?v=Qq6RYjY_inQ" onclick="window.open(this.href);return false;

good how to

http://www.whitearmor.net/forum/topic/2 ... ead/page-3" onclick="window.open(this.href);return false;

[RWinsel]

The frown could be w wee bit more pointy, but falls in the parameters.

Alrighty thanks! Can you point me in the direction of how to assemble the forearms?

I would use this for a start.

I would not use the CA glue but either E6000 or Amazing Goop

CA glue holds fast but is not water/moisture proof and will not hold after a point....

Video on the basics

https://www.youtube.com/watch?v=Qq6RYjY_inQ" onclick="window.open(this.href);return false;

good how to

http://www.whitearmor.net/forum/topic/2 ... ead/page-3" onclick="window.open(this.href);return false;

Thanks Tom! and yes im using e6000. Ive started the forearms and will post pics soon. In the meantime, how's this for trimming the brow a wee bit?

[RogueTrooper]

Thanks Tom! and yes im using e6000. Ive started the forearms and will post pics soon. In the meantime, how's this for trimming the brow a wee bit?

I would trim it just a wee bit more . Take a look at the side by side

[RWinsel]

Very good reference! How does this look?

[RogueTrooper]

the brow height looks good now.

the flat head ear bolts need the white paint.

I have seen the front and both left and right sides, hows the back look?

[RWinsel]

the brow height looks good now.

the flat head ear bolts need the white paint.

I have seen the front and both left and right sides, hows the back look?

Just regular white enamel model paint?

Heres the back. Thank you

[RogueTrooper]

Yeah any white enamel paint (with a sheen)

best to use a white primer first (make the enamel hold better)

I normally just take the era bolts off and primer them with krylon white primer spray paint (let dry) that add them back on ears then use a gloss white enamel model with a brush after getting them tighten down...

The back looks good, but the bottom inside corners of the decals look to be pulling a way etc.. (the way the lighting hitting them)

the brow height looks good now.

the flat head ear bolts need the white paint.

I have seen the front and both left and right sides, hows the back look?

Just regular white enamel model paint?

Heres the back. Thank you

[RWinsel]

Ok Tom, thanks so much for all the help!

[RogueTrooper]

Ok Tom, thanks so much for all the help!